User manual ZYXEL ZYAIR G-220 V2

[. . . ] ZyXEL G-220 v2 802. 11g Wireless USB Adapter User's Guide Version 1. 00 Edition 2 3/2006 ZyXEL G-220 v2 User's Guide Copyright Copyright © 2006 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. [. . . ] ASCII WEP keys are case sensitive. Back Next Exit Click Back to go to the Site Survey screen to select and connect to another network. Click Next to confirm your selections and advance to the Confirm Save screen. Click Exit to return to the Site Survey screen without saving. 3. 3. 2. 2 WPA-PSK/WPA2-PSK Figure 17 Station Mode: Security Settings: WPA-PSK/WPA2-PSK 40 Chapter 3 Wireless Station Mode Configuration ZyXEL G-220 v2 User's Guide The following table describes the labels in this screen. Table 7 Station Mode: Security Settings: WPA-PSK/WPA2-PSK LABEL Encryption Type DESCRIPTION The encryption mechanisms used for WPA/WPA2 and WPA-PSK/WPA2-PSK are the same. The only difference between the two is that WPA-PSK/WPA2-PSK uses a simple common password, instead of user-specific credentials. Select the encryption type (TKIP or AES) for data encryption. Refer to Section 2. 2. 3 on page 29 for more information. Type a pre-shared key (same as the AP or peer device) of between 8 and 63 casesensitive ASCII characters (including spaces and symbols) or 64 hexadecimal characters. Click Back to go to the Site Survey screen to select and connect to another network. Click Next to confirm your selections and advance to the Confirm Save screen. Click Exit to return to the Site Survey screen without saving. Pre-Shared Key Back Next Exit 3. 3. 2. 3 WPA/WPA2 Figure 18 Station Mode: Security Settings: WPA/WPA2 The following table describes the labels in this screen. Table 8 Station Mode: Security Settings: WPA/WPA2 LABEL Encryption Type DESCRIPTION The encryption mechanisms used for WPA/WPA2 and WPA-PSK/WPA2-PSK are the same. The only difference between the two is that WPA-PSK/WPA2-PSK uses a simple common password, instead of user-specific credentials. Select the encryption type (TKIP or AES) for data encryption. Refer to Section 2. 2. 3 on page 29 for more information. Select an authentication method from the drop down list. This is the user name that you or an administrator set up on a RADIUS server. Authentication Type Login Name Chapter 3 Wireless Station Mode Configuration 41 ZyXEL G-220 v2 User's Guide Table 8 Station Mode: Security Settings: WPA/WPA2 LABEL Password Certificate DESCRIPTION This field is not available when you select TLS in the Authentication Type field. Enter the password associated with the user name above. This field is only available when you select TLS in the Authentication Type field. Select a certificate from the drop-down list box. Note: You must first have a wired connection to a network and obtain the certificate(s) from a certificate authority (CA). Consult your network administrator for more information. Validate Server Certificate PEAP Inner EAP Select the check box to check the certificate of the authentication server. This field is only available when you select PEAP in the Authentication Type field. Click Back to go to the Site Survey screen to select and connect to another network. Click Next to confirm your selections and advance to the Confirm Save screen. [. . . ] Repeat the above two steps for each IP address you want to add. Configure additional default gateways in the IP Settings tab by clicking Add in Default gateways. In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. To manually configure a default metric (the number of transmission hops), clear the Automatic metric check box and type a metric in Metric. [. . . ]